Which is better 6061 or 7075 aluminum?

If you ask the question: what is the most commonly used aluminum alloy in the world?

The answer will be 6061 Aluminum, primarily due to its great strength, heat treatability, and relatively easy machinability and weldability. The main alloying elements of 6061 are magnesium and silicon. These elements give it a competitive edge in maintaining corrosive resistance even when the surface is braided. It can also be anodized for an additional thin layer of protection with various colors if that isn’t enough.

6061 is available in many forms including extrusion, sheets, and architectural shapes. It’s necessary to point out that 6063 Aluminum is also a popular choice in the 6000 series. However, its surface finish is far smoother than other commercial alloys. And its strength is roughly half that of 6061, which is because while the main alloying elements are magnesium and silicon, it has far lower levels of each. This makes it suitable for applications where strength doesn’t matter the most such as non-loadbearing posts and roofs or decorative structures.

WayKen has abundant experience in CNC machining 6061 aluminum and 6063 aluminum.

When it comes to structural metal fabrication, perhaps only one metal gets anywhere near the attention given to steel, and that is aluminum. It’s roughly a third of the weight of steel while still having exceptional mechanical properties. However, not all aluminum grades have the same properties, so it is critical to understand the differences among aluminum alloy grades during the material selection process. Two of the most popular aluminum alloy grades for structural applications are 6061 and 7075. While similar in some ways, there are also large differences worth noting.

What are the Differences Between 6061 and 7075 Aluminum?

The main differences between 6061 and 7075 aluminum are the following attributes:

• • Alloy Series & Chemical Composition
  • Mechanical Properties
  • Fabrication Considerations
  • Applications

Alloy Series and Chemical Composition

The first difference between 6061 and 7075 can be found right away just by looking at their number designations. 6061 is in the 6XXX series of aluminum alloy grades and 7075 is in the 7XXX series. Knowing this, without even digging into their individual material data sheets, it can be deduced that 6061 will have a higher amount of silicon, and that 7075 will have a much higher amount of zinc. Upon inspection of the exact ranges of the two individual alloys, it can also be noted that both have significant amounts of magnesium, although 7075 has slightly more. 7075 also has greater additions of copper in its chemical makeup.

Mechanical Properties

Both 6061 and 7075 are heat-treatable, so their mechanical properties cannot be compared accurately without assuming the same type of heat treatment. When looking at both alloys in the -T6 condition (meaning solution heat-treated then artificially aged), several noticeable differences are observed. First off is that the tensile strength of 7075-T6 is nearly double that of 6061-T6. The shear strength of 7075-T6 is roughly 1.5 times that of 6061-T6. The former is substantially harder as well.

Fabrication Considerations

6061 nearly always has the edge over 7075 when it comes to fabricating the two aluminum alloy types. This is mostly due to 6061 having a lower hardness and tensile strength. The lower hardness allows it to be machined more easily than 7075. The lower tensile strength means that 6061 is easier to form than 7075. While both materials can be joined by soldering, brazing or adhesives, 6061 is weldable and 7075 is generally considered not weldable. Even though 6061 is considered weldable, care must be taken to select the proper weld filler metal. Post-weld heat treatment and aging may be required to get the weld area back to the original “-T” designation. 7075 is extremely prone to cracking following welding.

Applications

There is much application overlap between the 6061 and 7075 aluminum alloys. As previously mentioned, both are structural grades of aluminum. Both are used for bike parts, aerospace components, and building construction. They differ in these areas on how they are used though. For instance, in the aerospace industry, 7075 may be more likely to be used as a gear or rod, and 6061 may be more likely to be implemented in an area that requires more ductility. With bike parts, some riders prefer the increased strength that comes with the 7075 aluminum alloy. 7075 is more likely to be used for molds and industrial tooling than 6061. Since it is more formable than 7075, 6061 is used more often for tanks, as well as other shapes with rounded contouring.